Small Fan Filter Kit - 4" up to 110 m3/h airflow rate
Hydroponics Fan, Filter & Duct Kit
A great little fan kit designed for small growing area's with no more than 2.5m duct run.
Ideal for small LED & CFL setups
Quiet
110m3/hr Centrifugal Fan (cable & UK plug fitted)
100mm Carbon Filter Filter
5m of Flexible Duct
Duct Clip x 3
Fan
Single speed fan 
comes with stand attached to screw to floor (can not see in picture)
Up to 110 m3/h.
Quiet operation
Power lead & UK Plug supplied 
Filter
activated carbon filter.
100mm 4” dia
18 month life span under normal conditions.
Duct
5m length
Rest of kit
Jubilee worm drive clip x 3

In this kit you will get the following item:

Ballast 600w ---- 600w Bulb Dual Spectrum ---- Reflector

Tent - 1.2m2

Swiftair Inline fan kit - Centrifugal fan, Carbon Filter, Alu Ducting, Clamps

Yo Yo Hanger (Pair)

1 x Coco CANNA Natural 50 Ltr

1 x CANNA Coco A+B

Please see below for description on products:

The 600w Ballast, has been designed for improved quality and high output,

✓ Metal Case

✓ Fitted with IEC connector cord and UK mains lead

This produces the full light spectrum with added blue for the propagation and vegging stages. We recommend you replace lamps every 3-6 months to avoid diminishing harvests.

Lamp size and output

600 watt - 90,000 Lumens

Please keep the retail packaging in case you need to return it to us. Bulbs sent without the original packaging are not covered by warrant

SUPERB VALUE HYDROPONIC TENT 120 x 120 x 200

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

4 x Air holes (1 Left, 1 Right, 1 on Top & 1 Bottom)

Passive ventilation windows: 3

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

PowerPlant Heavy Duty Timer - Please select if needed

Normal household timers are not built to take the high inductive loads produced by HID ballasts. If used with an HID ballast - the contacts inside the timer that open and close the timed circuit will overheat and weld together - breaking the timer and leaving your grow lights permanently on.

The PowerPlant Heavy Duty Timer is different. It is designed to take high loads and has no problem dealing with the inductive loads produced by a 600w ballast.

This means no separate contactor is required and saves you money. It has a 96 switching operations within a 24 hour period (every 15 minues).

This timer is suitable for timing one 600w HID ballast. It has a robust case design with socket and timer dust/moisture covers. This unit is ideal for timing 400w and 600w ballasts. Do not use more than one 600w ballast per timer.

 Please Choose Above Which Size You Require

Reflector

A simple Dutch barn style reflector. It is open-ended, highly polished and dimpled lightweight reflector, which gives an efficient and even distribution of light.

Sodium HPS Lamp

Sodium HPS offers exceptionally high output. Couple this with raised spectral discharge in the reds and blues (exactly the right spectral energy distribution curves that your plants need to thrive) and a long lamp life, and you have the perfect plant grow light. This lamp also has 32,000 life hours and colour temperature of 2000K.

250w = 33000 lumens

400w = 50000 Lumens

600w = 94000 lumens

Spectral output changes in a HPS lamp as it ages. We recommend changing your lamp every 9-12 months for optimum growth conditions

Ballast

Ballast enclosures are made from heavy gauge steel and are powder coated to ensure a hard wearing finish. Thoroughly tested to ensure each product is in full working order and is electrically safe.

Plug & Play Lead

Vented for Cool Operation

Wall Mountable

UK Plug

Lighting Timer

24 hour plug and play timer

Will control up to 13 amps

Can be set to switch from 15 minute intervals

SMF Standard Model with Plug

Kit Comes with the following

5m - Aluminium ducting

3 x Clamps

4" 5" 6" Fan with Plug

Standard Model Comes with plug how ever this does not need to be used if not needed

SMF fans are applied for supply and exhaust ventilation systems of commercial, office, tents, carbon filters and other premises etc.

Compatible with Ø 100, 125, 150mm round air ducts.

Due to the corrosion-resistant durable plastic casing, these models are the perfect solution for the installation in exhaust ventilation systems in humid premises such as bathrooms, kitchens etc.

Ballast 600w ---- 600w Bulb Dual Spectrum ---- Reflector

Tent - 0.8m2

Swiftair Inline fan kit - Centrifugal fan, Carbon Filter, Alu Ducting, Clamps

Canna CoCo Natural 50 litre

Canna A+B 1 Litre

Fabric Pots 11 litre x 2

Yo Yo Hanger (Pair) - Please select

Timer - Please select

Please see below for description on products:

The 250w Ballast, has been designed for improved quality and high output,

✓ Metal Case

✓ Fitted with IEC connector cord and UK mains lead

This produces the full light spectrum with added blue for the propagation and vegging stages. We recommend you replace lamps every 3-6 months to avoid diminishing harvests.

Lamp size and output

600 watt - 90,000 Lumens

Please keep the retail packaging in case you need to return it to us. Bulbs sent without the original packaging are not covered by warrant

SUPERB VALUE HYDROPONIC TENT

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

5 x 150mm Air holes (2 Left, 2 Right & 1 on Top)

1 x 80mm hole

Passive ventilation windows: 2

In this kit you will get 

1 x 600w LED light

1 x 1.2mx1.2mx2m Tent

4 x 10L pots 

1 x 50L Bag Canna Natural

1 x 4" Fan Kit

1 x Grow and Bloom Swift 1L

SUPERB VALUE HYDROPONIC TENT

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

LED Power: 600W 

Power Consumption: energy saving, consumes 120W

Led chip: Epistar, double chips

LED Quantity: 60PCS 10W LEDs

Coverage Area: 3 about 3.6 x 4 Square Feet ( The lighting area and the height are changeable according to different plants and environments )

Colour: red 39pcs, blue 11pcs, orange 4pcs, white 4pcs, IR 1pcs and UV 1pcs

Full Spectrum: 430~440nm, 450~475nm, 620~630nm, 650~660nm,3500K and 6000k,IR 730nm,UV 410nm

Lumen: 7124.00lm

Fan Kit

Air Flow

Centrifugal fan - 110 m3/h - comes with stand attached to screw to floor (can not see in picture)

Carbon Filter Size

To get the most out of your kit, please follow these few tips:

Remember, if you reverse-mount your Filter you will lose the benefit of your pre-filter and reduce the life of the carbon.

Always mount your filter as high as possible. Hot air naturally rises and so will your odours!

Try not to block too much of the filter with mounting straps or hanging devices. Use the ends of the filter to support, so not to inhibit the surface area of the filter.

Do Not mount your Filter near to humidifiers. Humid air over 85% may enter the filter rendering the activated carbon ineffective and your filter may NOT neutralise odours!

Ensure you have an airtight seal around the connection of your filter to ducting or extractor fan.

SUPERB VALUE HYDROPONIC TENT

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

PowerPlant Heavy Duty Timer - Please select if needed

PLease select which LED you require

LED Power: 600W 

Power Consumption: energy saving, consumes 120W

Led chip: Epistar, double chips

LED Quantity: 60PCS 10W LEDs

Coverage Area: 3 about 3.6 x 4 Square Feet ( The lighting area and the height are changeable according to different plants and environments )

Colour: red 39pcs, blue 11pcs, orange 4pcs, white 4pcs, IR 1pcs and UV 1pcs

Full Spectrum: 430~440nm, 450~475nm, 620~630nm, 650~660nm,3500K and 6000k,IR 730nm,UV 410nm

Lumen: 7124.00lm

LED Power: 1000W 

Power Consumption: energy saving, consumes 190W

Led chip: Epistar, double chips 

LED Quantity: 100PCS 10W LEDs

Coverage Area: about 4.2 x 4.6 Square Feet ( The lighting area and the height are changeable according to different plants and environments ) 

Colour: red 71pcs, blue 14pcs, orange 8pcs, white 4pcs, IR 1pcs and UV 1pcs . 

Full Spectrum: 430~440nm, 450~475nm, 620~630nm, 650~660nm,3500K and 6000k,IR 730nm,UV 410nm 

Lumen: 11823.00lm

LED Power: 1500W 

Power Consumption: energy saving, consumes 260W 

Led chip: Epistar,double chips 

LED Quantity: 150PCS 10W LED 

Coverage Area: about 6.5 x .6.5 Square Feet ( The lighting area and the height are changeable according to different plants and environments ) 

Colour: red 108pcs, blue 20pcs, orange 10pcs, white 10pcs, IR 1pcs and UV 1pcs 

Full Spectrum: 430~440nm, 450~475nm, 620~630nm, 650~660nm,3500K and 6000k,IR 730nm,UV 410nm 

Lumen: 16813.00lm

Power: 2000W 

Power Consumption: energy saving, consumes 375W

Led chip: Epistar,double chips 

LED Quantity: 200PCS 10W LEDs 

Coverage Area: about 7.5 x .7.5 Square Feet ( The lighting area and the height are changeable according to different plants and environments ) 

Colour: red 132pcs, blue 36pcs, orange 14pcs, white 14pcs, IR 1pcs and UV 1pcs . 

Full Spectrum: 430~440nm, 450~475nm, 620~630nm, 650~660nm,3500K and 6000k,IR 730nm,UV 410nm 

Lumen 22853.00lm

Fan Kit

Air Flow

Centrifugal fan - 110 m3/h - comes with stand attached to screw to floor (can not see in picture)

Carbon Filter Size

To get the most out of your kit, please follow these few tips:

Remember, if you reverse-mount your Filter you will lose the benefit of your pre-filter and reduce the life of the carbon.

Always mount your filter as high as possible. Hot air naturally rises and so will your odours!

Try not to block too much of the filter with mounting straps or hanging devices. Use the ends of the filter to support, so not to inhibit the surface area of the filter.

Do Not mount your Filter near to humidifiers. Humid air over 85% may enter the filter rendering the activated carbon ineffective and your filter may NOT neutralise odours!

Ensure you have an airtight seal around the connection of your filter to ducting or extractor fan.

A great step into Deep Water Culture, the single plant Oxypot grow systems produce phenomenal results in a small space and use very little media - just a handful of clay pebbles.

The plants are placed in a mesh pot containing pebbles and the roots hang down into the growing chamber which contains an air pump that continually oxygenates the nutrient solution.

One of the simplest introductions to hydroponics available.

Oxypot DWC (Deep Water Culture) systems submerge the roots of the plant in a highly oxygenated nutrient solution, encouraging very rapid growth.

The Oxypot is an ideal 1, 2, 4, 6 or 9 system.

The Kit includes

1 x Pump

1 x Air Stone

Mesh pot to suit

(please see picture if unsure)

The Oxypot XL & Oxypot 4 have reversible lids for lower plant suspension during the veg stage.

Size L x W x H cm

Oxypot Complete Kit      -   35 x 35 x 38  - 1 Plant

Oxypot XL Complete Kit   -  83 x 58.5 x 38  - 2 Plant

Oxypot XL+ (6.5L Basket) Complete Kit   -  83 x 58.5 x 38  - 1 Plant

Oxypot 4 Complete Kit     - 83 x 83 x 38  - 4 Plant

Oxypot V6 Complete Kit   -  83 x 58.5 x 38  - 6 Plant

Oxypot V9 Complete Kit     - 83 x 83 x 38  - 9 Plant

Small Fan Filter Kit - 4" up to 110 m3/h airflow rate
Hydroponics Fan, Filter & Duct Kit
A great little fan kit designed for small growing area's with no more than 2.5m duct run.
Ideal for small LED & CFL setups
Quiet
110m3/hr Centrifugal Fan (cable & UK plug fitted)
100mm Carbon Filter Filter
1.5m of Semi Rigid Duct (better air flow)
Duct Clip x 3
Fan
Single speed fan 
comes with stand attached to screw to floor (can not see in picture)
Up to 110 m3/h.
Quiet operation
Power lead & UK Plug supplied 
Filter
activated carbon filter.
100mm 4” dia
18 month life span under normal conditions.
Duct
1.5m length
Rest of kit
Jubilee worm drive clip x 3

In this kit you will receive:

(Code: SW-DIG-600) Swiftair Digital Ballast x 1
(Code: REFLECT9EU) Reflector x 1
(Code: HPS600W) 600w HPS Bulb x 1

Settings: 250w - 400w - 600w - 600wSL
Super Lumens - Boosts lumen output by 10% at the flip of the switch
Has “soft-start” program to allow multiple ballasts to start at the same time
Power factor of 99.9% - lose fewer watts from the power supply to the lamp
Runs on 120 to 240 volt power, 50 hertz or 60 hertz
Works with both Metal Halide (MH) and High Pressure Sodium (HPS) lamps
External breaker system protects against power surges 
Low noise while in operation 
Come with an 2m power cord - Uk Plug
High Quality, 1-Year factory warranty

Please Select which size you require above

In this kit you will get the following LUMii products

LUMii METTA Ballast

LUMii MAXii Reflector

LUMii Sunblaster Bulb or POWERPLANT Metal Halide Bulb

Ballasts

LUMii METTA 600w ALLOY BALLAST

LUMii are constantly trying to improve there ballast range, and our latest addition is the robust metal cased LUMii Metta. 

✓ Metal case

✓ALLOY windings

✓ Can be used horizontally or vertically

✓ Cool running

✓ Fitted with IEC connector cord and UK mains lead

✓ Will fire your lamp up to 15m from your ballast

✓ 12 month guarantee from date of purchase

Currently only available in 600w, the Metta has the same great component quality and high output that you would expect from any of our LUMii ballasts. 

Fitted with super imposed-pulse ignitors, the ignition voltage is generated without placing a high voltage load on the choke, therefore extending the compact life. 

The LUMii Metta ballasts are well vented, meaning they are very quiet and cool running along with being safe and reliable. Fitted with IEC connector cord and mains lead, our newest addition is designed and tested in the UK.

Reflector

The LUMii MAXii is a simple and easy-to-use Dutch barn-style reflector. It is an open ended highly polished and dimpled lightweight reflector which gives an efficient and even distribution of light. Unlike others on the market, the LUMii MAXii includes a unique lamp holder that is adjustable and designed to fit all E40 lamp types. All earth requirements are incorporated into the lamp holder itself. This safety feature means that there is no need for additional components. 

A unique feature of this reflector is that with the addition of the LUMii HID to CFL Converter Set contains a short additional cord set to convert the supplied IEC to a conventional power supply as well as an innovative support device to assist with the additional weight of a CFL lamp and to make sure the lamp stays horizontal. 

With the LUMii MAXii system and the CFL Converter Ki,t you can use a cool CFL lamp for vegetative growth. Then if you are flowering switch to an HPS lamp by simply unplugging the converter plug and plugging into a LUMii ballast; all without taking your reflector down or changing it. No other reflector does this - it is easy!

L: 470mm x W: 430mm x H: 190mm

Bulbs 600w HPS

The LUMii SunBlaster lamp - 600w. The 600w lamp gives an output of 155 lumens per watt (93000 lumens).

The crystal glass used offers consistant thickness which allows a more even light output. There is raised blue levels in the spectrum output. 

The design of the lamp has avoided the use of barium film which means no blackening of the glass and less gas impurities in the lamp. It also allows for a cleaner more stable light output. 

The E40 mechanical double layer base design eliminates soldering and paste and delivers a 100% inline base.

Bulb 600w MH

Powerplant Metal Halide lamps are designed for your plants growth period as they deliver a blue spectrum of light at 4000 Kelvin.

Providing your plants with a pure blue spectrum of light will encourage them to become much bushier with thicker stems and lush green growth and this will help to maximise the potential of your plants when you enter your flowering period.

Powerplant MH lamps are retro fit and are designed to work with any type of ballast, even if you only specifically have a ballast for HPS lamps, these lamps will still work with a life expectancy of around 10,000 hours. Lumen Output

Powerplant MH 600w lamp - 51,000 lumens

E40 Screw Fitting

Swiftair - SF Inline fan

Kit will include the following depending on selection: 

4" 100mm Kit: SF100S - UK Plug - 5m Alu Duct - Carbon Filter 4" - 3 x Clamps
5" 125mm Kit: SF125S - UK Plug - 5m Alu Duct - Carbon Filter 5" - 3 x Clamps
6" 150mm Kit: SF150S - UK Plug - 5m Alu Duct - Carbon Filter 6" - 3 x Clamps

Carbon Filter Details
4" carbon filter - 4" x 250mm
5" carbon filter - 5" x 400mm
6" carbon filter - 6" x 500mm

Fan Details (M3/hr at free air)
SF100S - On/Off - 100 m3/h
SF125S - On/Off - 150 m3/h

SF150S - On/Off - 210 m3/h

DESCRIPTION

Please choose between basic or Complete

Basic - Grow System and Pump

Complete Kit - Grow System, Pump, Spreader Mat, pH Test kit, pH Down, and emptying tube

HOW IT WORKS

In NFT plants and placed in the grow system without any extra growing media - say goodbye to lugging bags of soil and coco around! 

Nutrient solution is constantly pumped over bare roots and the run-off flows back into the reservoir. 

Growth is fast and healthy because there's no soil to restrict root access to the constantly available water, nutrients and oxygen. 

To transfer plants into the Gro-Tank or Multi-Duct just tip the plant out of its pot and place it straight into the Gro-Tank or Multi-Duct tray without adding any extra media. 

If you've started in rockwool just place the rockwool block directly onto the Gro-Tank or Multi-Duct tray when you're ready to transplant. 

Switch to NFT and you'll never switch back!

Gro-Tanks

System Size - L x W cm   -  No. of Plants - Tank Volume

GT/GN205 - 70 x 30 - 1-3 - 20L

GT/GN424 - 101 x 49 - 3-5 - 45L

GT/GN604 - 153 x 49 - 5-8 - 60L

GT/GN901 - 211 x 53 - 6-12 - 80L

GT/GN100 - 120 x 107 - 9-16 - 100L

GT/GN150 - 1186 x 100 - 15-25 - 85L

Perfect for growers who want to: 

Use less media

Grow tall plants in a low space – so need a low-level system

Get used to one system and scale up to larger systems over time – available for up to 25 plants

In this Kit you will receive the following:

SMF100S with UK Plug (220 m3/hr) x 1

Aluminium Ducting 5m x 1

Carbon filter 4" 100mm x 10" 250mm x 1

Clamps x 6

Choose between a: 40 x 40 x 140 Tent or 80 x 80 x 180 Tent

Choose Between:

250w or 600w hps Light kit

125w, 150w or 250w CFL Light Kit

Please see details below:

4" 100mm x 10"250mmCARBON FILTER

- CARBON FILTERS FOR ODOUR REMOVAL

- 50% FREE AREA FOR LESS AIRFLOW REDUCTION

- HIGH QUALITY PACKAGING AND BOXING FOR EASY TRANSPORTATION

On delivery: The carbon filter can some times have carbon dust come through to the white outer casing making it blackish or grey this is not a issue and fine to use as long as the carbon filter is not dented.

Swiftair 100mm – Mixed flow fan.

Quiet and powerful, high performance up to 220 m3/hr.

Main Features

Quiet and powerful mixed flow fan

UK Plug attached

2 Speed Switch on Fan

High performance up to 220 m3/hr (30 Watts)

Low Speed 160 m3/hr (24 watts)

Sound Level 35 dB (3m)

Remote mounting in lofts and cupboards

Double-up – Two fans in series – double the pressure

Two fans in parallel – double the flow

Thermally protected motor

TENT 80 x 80 x 180

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

5 x 150mm Air holes (2 Left, 2 Right & 1 on Top)

1 x 80mm Air hole

Passive ventilation windows: 2

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

TENT 40 x 40 x 140

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

Reflector

A simple Dutch barn style reflector. It is open-ended, highly polished and dimpled lightweight reflector, which gives an efficient and even distribution of light.

CFL Lamp

Our CFL units feature ultra high output compact fluorescent lamps Cool White

Luminous (lm) - Cool White 6400K

125w - 7500 lm

150w - 9000 lm

250w - 15000 lm

They’re available in cool white spectrum, making them ideal for: Propagation ,Over wintering plants, Side lighting, Mother Plants

Designed to help you get the best out of your plants, whilst still giving you great convenience, the CFL Lamps offer you a host of benefits: They provide your plants with lots of usable light for best growth and yield, They give off very little heat, meaning you can place them close to your plants for maximum output, As the lamps are self-ballasted, you simply screw the CFL into your reflector, giving you great convenience and flexibility – as well as cost savings.

Available in 125w, 150w or 250w kit comes with Reflector and plug converter

Sodium HPS Lamp

Sodium HPS offers exceptionally high output. Couple this with raised spectral discharge in the reds and blues (exactly the right spectral energy distribution curves that your plants need to thrive) and a long lamp life, and you have the perfect plant grow light. This lamp also has 32,000 life hours and colour temperature of 2000K.

250w = 33000 lumens

600w = 90000 lumens

Spectral output changes in a HPS lamp as it ages. We recommend changing your lamp every 9-12 months for optimum growth conditions

Ballast

Ballast enclosures are made from heavy gauge steel and are powder coated to ensure a hard wearing finish. Thoroughly tested to ensure each product is in full working order and is electrically safe.

Plug & Play Lead

Vented for Cool Operation

Wall Mountable

UK Plug

Lighting Timer

24 hour plug and play timer

Will control up to 13 amps

Can be set to switch from 15 minute intervals

Manual override

Wilma drip irrigation systems are designed to provide high yields in as simple a way as possible.

Available in a range of sizes to suit the modern grower, the Wilma system has been developed to include:

- Improved spacing between pots

- A handy nutrient mixing tap

- Easier access to the reservoir

Why yields are bigger when using a Wilma

The Wilma is like a pot with a personal assistant!

The Wilma feeds the plants little and often, which provides the plants with more water and nutrients than if they were hand-watered

When watering once per day you can't give a plant all the water and nutrients it needs for optimum growth because you would waterlog the medium and starve the plant of oxygen.

In a Wilma the plants are provided with water and nutrients little and often, so they are able to take up more water and nutrient and they are never over or underfed or watered, so the Wilma produces bigger yields compared with pots.

Because of the frequent watering clay pebbles can be used which allow much more air around the roots than any other growing medium - and better access to oxygen = bigger yields.

Plants benefit from the accurate feeding of active hydroponics and you benefit from the simplicity and flexibility of growing in pots.

The ideal step up from a pot.

Golden Rule: Use the correct dripper for the growing medium. When growing in clay pebbles, use the flood drippers. For more absorbent media – soil, coco, grow cubes, mapito – use the arrow drippers.

• If using clay pebbles treat the Wilma as a re-circulating hydroponic system and top up the tank every few days with half strength nutrient solution.

• If using an absorbent medium - like soil, coco or rockwool - treat the Wilma as a dripper system with a catchment tank. The aim is to minimise run off and top up the tank with full strength nutrient solution.

• Use a cleaning product, like Atami’s ATAclean, to prevent dripper blockage.

• Set feeds on a segmental timer: when plants are young start with 2x or 3x 15minute feeds a day when using clay pebbles. Set 1x or 2x 15minute feeds a day when using an absorbent medium. Increase the number of feed periods as plants mature.

Description                                         No. of Plants                      Size L x W cm

Small 4 (6L) Pots                               4                                              60 x 60

Small 4 (11L) Pots                            4                                              60 x 60

Large 4 (11L) Pots                            4                                              75 x 75

Large 4 (18L) Pots                            4                                              75 x 75

Large 8 (6L) Pots                               8                                              75 x 75

XL 4 (25L) Pots                                   4                                              90 x 90

XL 4 (18L) Pots                                   4                                              90 x 90

XL 8 (11L) Pots                                   8                                              90 x 90

XXL 5 (25L) Pots                                5                                              115 x 115

XXL 8 (18L) Pots                                 8                                              115 x 115

XXL 9 (18L) Pots                                 9                                              115 x 115

XXL 16 (11L) Pots                              16                                           115 x 115

XXL 20 (6L) Pots                                 20                                           115 x 115

Small Wide 8 (11L) Pots                 8                                              120 x 60

Small Wide 10 (6L) Pots                 10                                           120 x 60

Large Wide 8 (11L) Pots                 8                                              170 x 75

Large Wide 8 (18L) Pots                 8                                              170 x 75

XL Wide 8 (18L) Pots                       8                                             190 x 90

XL Wide 8 (25L) Pots                       8                                             190 x 90

Feed Time Guide for coco/soil                       Feed Time Guide for 60/40           Feed Time Guide for pebbles

Start                      1x 15 minute feed per day                           2 x 15 minutes feeds per day      2 x 15 minutes feeds per day

Veg                        2 or 3 x 15 minute feeds per day               3 x 15 minute feeds per day        3-4 x 15 minute feeds per day

Flowering            3 to 5 x 15 minute feeds per day               4-5 x 15 minute feeds per day    4-6 x 15 minute feeds per day

As with all methods of growing increase or decrease feeds according to plant requirements

Standard Stand - 106 cm (diameter)

Inner Pot Punched - 9.5L - any media

Inner Pot Aqua - 6.5L Clay Pebbles

Inner Pot Culture - 6.5L Soil, Coco, Mixed Media

Outer pot Drilled - 26.5cm (diameter)

Copper Discs - 170mm - Aqua And Culture Pots

Copper Discs - 250mm - Punched Pots

X-Stream Aeroponic Propagation

Want to root cuttings faster, with a near 100% success rate and no root rot or drying out?

Then choose the X-Stream aeroponic propagator. The Xstream mists cuttings to maintain ideal moisture and oxygen levels.

Cuttings are suspended in mesh pots in the propagator’s misting chamber and are constantly misted.

DESCRIPTION

The X-Stream Aeroponic propagator creates perfect conditions for cultivating cuttings reliably and quickly.

The mist prevents root rot and drying out and provides unrestricted access to oxygen, the large vents in the lid provide humidity control, and the heated version enables you to raise cuttings in an unheated area all year.

Because the mist is constant, there’s no need to monitor water levels every day.

A higher % of your cuttings will root (many growers report 100% success rates) and the plants will be faster growing and more resistant to stress and disease throughout their life thanks to their incredibly healthy start.

X-Stream Aeroponic propagators have grooves in the lid to fit the Sunblaster T5 propagation lights. These nanotech enhanced lights run cool enough to be placed onto the propagator lids with zero risk of damage.

WHY THEY ARE GREAT

The X-Stream creates the perfect environment for root development which dramatically improves the success rate of cuttings and speeds up their root development. The condition of the cuttings can be checked quickly with minimal impact on the cutting ensuring that the cuttings are as healthy as possible when they are potted on.

X-Stream propagators have specially designed lids to fit Sunblaster T5 lights. Simply place the light onto the lid and your ready to grow. – SEE EBAY ITEM NUMBER – 262916423681

System Size L x W x H cm   -    Tank Volume    -    No. of plants

12 Site Propagator   -   59 x 46.5 x 44   -   8 Litres   -   12

20 Site Propagator   -   59 x 46.5 x 44   -   8 Litres   -   20

40 Site Propagator   -   77 x 40.5 x 45   -   14 Litres   -   40

120 Site Propagator   -   115 x 64.5 x 46    -   40 Litres   -   120

HINTS AND TIPS

Pump - leave the pump on 24/7~

Feeding - when roots begin to show add nutrients at a quarter of the manufacturers recommended dosage.

Ventilations - once roots are showing, open the vents slightly. Gradually increase the opening every day and remove the lid completely to harden off for a couple of days before transplanting on.

Rooting gels and powder can still be used. When the cutting is dipped, all active ingredients are absorbed immediately and will not be ‘washed off’ by the misting.

Transplanting into soil or coco

Remove from the X-Stream when roots begin to poke through the mesh pot. Pot on into 3” or 4” pots and grow on for a few days before transplanting on.

Transplanting into hydro

Remove from the X-Stream when roots have grown 3” to 4” from the bottom of the mesh pot. Transplant directly into the hydro system.

Transplanting into rockwool

Remove from the X-Stream when roots have grown 3” to 4” from the bottom of the mesh pot. Punch a hole in the bottom of a 3” or 4“ cube, sandwich the cutting between two halves of an Grodan SBS cube allowing the roots to trail through the punched hole. Transplant immediately.

This kit will include

1 x tent 1.2x2.4x2m

1 x fan kit (Fan x1, Ducting 5m x1, Carbon Filter x1, Clamps x3)

2 x Light kit 600w (Reflector x 2, HPS x 2, Ballast x 2)

Timers - Please select if needed

YoYo's - Please select if needed

Ballast Our Ballast is great for growers who have not moved on to digital ballast but still require a high quality lighting system.

A fully vented ballast to keep heat to a minimum.

~ Fully vented for maximum cooling and efficiency. (will still get hot)

~ Suitable for HP Sodium, Dual Spectrum and Metal Halide Lamps.

~ 600w Ballast Suitable for 600w HPS & MH Bulbs

~ Plug into your reflector with no additional wiring.

~ Fused and surge protected.

~ Sodium HPS Lamp

Sodium HPS offers exceptionally high output. Couple this with raised spectral discharge in the reds and blues (exactly the right spectral energy distribution curves that your plants need to thrive) and a long lamp life, and you have the perfect plant grow light. This lamp also has 32,000 life hours and colour temperature of 2000K. 600w = 90000 lumens

Small Fan Filter Kit - 4" up to 110 m3/h airflow rate

A great little fan kit designed for small growing area's with no more than 2.5m duct run.

Ideal for small LED & CFL setups

110m3/hr Centrifugal Fan (cable & UK plug fitted)

100mm Carbon Filter Filter

5m of Flexible Duct

Duct Clip x 3

Lumii Ballast
The new LUMii® 600w, has been redesigned for improved quality and high output, and continues to boast a fully enclosed and potted case. As with all LUMii® ballasts, you are able to get the true output that your plants need. Many ballasts on the market are underpowered to save money, but not LUMii®!
✓ Injection-moulded case in fire resistant glass filled nylon
✓ Can be wall mounted or used horizontally or vertically (slotted hanging hook incorporated)
✓ Quiet running
✓ Intelligent electronic timed ignitor
✓ Fitted with IEC connector cord and UK mains lead
✓ Will fire your lamp up to 15m from your ballast
✓ 12 month guarantee from date of purchase
LUMii Sunblaster
At different times in the growing cycle, plants require different types of light radiation. Immature plants have different needs to those about to mature.
To maximise the potential of a plant and ensure that it grows strong and healthy, you need to deliver just the right kind of light radiation. These bulbs have been enhanced to produce the perfect balance of blue and red light and benefit your plants at crucial stages in their development.
The SunBlaster Dual Spectrum lamp is scientifically designed and developed for the complete lifecycle of a plant. This produces the full light spectrum with added blue for the propagation and vegging stages.
Although these lamps are produced to an extremely high standard, the performance will drop off over time. We recommend you replace lamps every 3-6 months to avoid diminishing harvests.
Lamp size and output
SunBlaster 600 watt - 93,000 Lumens
Please keep the retail packaging in case you need to return it to us. Bulbs sent without the original packaging are not covered by warrant
LUMii MAXii Reflector
It is an open ended highly polished and dimpled lightweight reflector which gives an efficient and even distribution of light. Unlike others on the market, the LUMii MAXii includes a unique lamp holder that is adjustable and designed to fit all E40 lamp types. All earth requirements are incorporated into the lamp holder itself. This safety feature means that there is no need for additional components. 
With the LUMii MAXii system and the CFL Converter Ki,t you can use a cool CFL lamp for vegetative growth. Then if you are flowering switch to an HPS lamp by simply unplugging the converter plug and plugging into a LUMii ballast; all without taking your reflector down or changing it. No other reflector does this - it is easy!
L: 470mm x W: 430mm x H: 190mm
The LUMii MAXii comes as a complete HID reflector set and is supplied with hanging hooks as per picture
Size: LITE 2.4m - 1.2m x 2.4m x 2m
Air extraction through the roof via a 250mm (10”) sock
2 x inline 250mm (10”) socks for use with air-cooled lighting
2 x passive air fine (anti-mite) mesh vents at base with light-proof covers when not in use
Recommendations:
Ideal for 2 large plants or 8 mid-size plants
Two lamp set up - 2 x 600w HID
PowerPlant Heavy Duty Timer - Please select if needed
Normal household timers are not built to take the high inductive loads produced by HID ballasts. If used with an HID ballast - the contacts inside the timer that open and close the timed circuit will overheat and weld together - breaking the timer and leaving your grow lights permanently on. 
The PowerPlant Heavy Duty Timer is different. It is designed to take high loads and has no problem dealing with the inductive loads produced by a 600w ballast. 
This means no separate contactor is required and saves you money. It has a 96 switching operations within a 24 hour period (every 15 minues). 
This timer is suitable for timing one 600w HID ballast. It has a robust case design with socket and timer dust/moisture covers. This unit is ideal for timing 400w and 600w ballasts. Do not use more than one 600w ballast per timer.
Fan Kit 

FAN, ALUMINIUM DUCTING, CARBON FILTER, CLAMPS X 3
Air Flow
Centrifugal fan - 110 m3/h - comes with stand attached to screw to floor (can not see in picture)
Carbon Filter Size
To get the most out of your kit, please follow these few tips:
Remember, if you reverse-mount your Filter you will lose the benefit of your pre-filter and reduce the life of the carbon. Always mount your filter as high as possible. Hot air naturally rises and so will your odours!
Try not to block too much of the filter with mounting straps or hanging devices. Use the ends of the filter to support, so not to inhibit the surface area of the filter.
Do Not mount your Filter near to humidifiers. Humid air over 85% may enter the filter rendering the activated carbon ineffective and your filter may NOT neutralise odours!

Ensure you have an airtight seal around the connection of your filter to ducting or extractor fan.

FREE - 5ml Pipette!!
Narrow Spectrum kit - Our ESSENTIALS pH Test Kit is good for 150 tests. At a rate of 3 tests per week, it will last one year. This makes it excellent value for money. Covers a pH range of 5.6-7.4 measuring in 0.2 increments.

Wide Spectrum kit - Our ESSENTIALS pH Test Kit is good for 150 tests. At a rate of 3 tests per week, it will last one year. This makes it excellent value for money. Covers a pH range of 4-8.5 measuring in 0.5 increments.

AutoPot XL - 25 Litre

The AutoPot 1 Pot XL Pot System comes supplied with a tray that accommodates a 25 litre pot and a Root Control Disc that is placed under the pot in the tray cavity with the gold side face up.

The Root Control Disc or RCD will prevent roots from leaving the pot and discourage them from heading towards the AQUAvalve.

You will also receive an AQUAvalve that controls the water supply and 1.5 metres of 4mm pipe that supplies the water to the system.

The AutoPot 1 Pot XL Pot System is extremely versatile and can be used for a wide range of plant types and sizes.

Seasonal flowering plants and perennial shrubs thrive and produce an abundance of blooms and foliage because of the unique action of the AQUAvalvue that has been designed to allow the plant to go through a wet and dry cycle.

The AutoPot 1 Pot XL Pot System is easily extended so many pots can be linked to a single tank.

The pots and tray can be easily moved at will meaning that if the plants grow too large they can be spaced further apart with ease.

Once the system is set up and the tank is filled with water and liquid feed the system will take care of all your plant's needs.

All you need to do is remember to fill your tank from time to time.

Omega Lighting kits, are regarded as the best on the market and excellent value for money. 
This combination package offers your customers a high performance, cost effective lighting system. 
Included in the package is a high quality digital, dimmable Ballast, an open-ended, highly polished, dimpled lightweight EuroWing reflector, which gives an efficient and even distribution of light, as well as a 600W grow lamp of your choice (depending on your customers growing requirements).
DIGITAL BALLAST
This top of the range dimmable Ballast features a unique 4-setting control which offers dimming options of 250W, 400W, 600W and a super-lumen setting of 660W. 
All Ballasts feature a 1 metre mains lead with flying IEC lead for safety and are wall mountable. CE certified and guaranteed.
SUPER HPS BULB
Dense red spectrum promoting unrivalled yields and rapid growth, ideal for flowers. Viscous Lumen output and consistency. All Omega lighting bulbs carry CE mark and a minimum of one year's guarantee.
DUAL SPECTRUM BULB
Broader hitting spectrums are achieved by tweaking the PAR range suitable for plants from start to finish. Ideal for both flowers and vegetables. 
Added UV for ripening and hardening. All Omega lighting bulbs carry CE Mark and a minimum of one year's guarantee.
METAL HALIDE BULB
Our metal halide grow bulbs use a blue spectrum which plants need when in a vegetable stage. This prevents plants stretching and instead gives a short dense plant ready for flowering. 

All Omega lighting bulbs carry CE mark and a minimum of one year's guarantee.

LUMii SOLAR 315 and 630 are the latest horticultural lighting solutions to be offered by LUMii

The LUMii Solar 315 and 630 are complete fixtures that power 315W ceramic discharge metal-halide (CDM) lamps to give your plants the best possible spectrum of light.

The SOLAR 630 offers two power switches, one for each lamp, allowing you to choose which lamps you want on/off. They  are suitable for all CDM 315w lamps.

- Full fixture (ballast & lamp)

- Short circuit protection

- Use for both supplementary and stand alone lighting

- Extremely high PAR levels

Power

110v - 240v

PF

>0.99

Input HZ

50/60

TA (degree C)

0-40

LUMii BLACK Ballast
LUMii MAXii Reflector
LUMii Sunblaster Bulb
Ballasts
The new LUMii® BLACK, available in 600w, has been redesigned forimproved quality and high output, and continues to boast a fully enclosed and potted case.
As with all LUMii® ballasts, you are able to get the true output that your plants need. Many ballasts on the market are underpowered to save money, but not LUMii®!
✓ Metal Case
✓ Can be wall mounted or used horizontally or vertically (slotted hanging hook incorporated)
✓ Quiet running
✓ Intelligent electronic timed ignitor
✓ Fitted with IEC connector cord and UK mains lead
✓ Will fire your lamp up to 15m from your ballast
✓ 12 month guarantee from date of purchase
Bulbs 600w
The LUMii SunBlaster lamp is available in two sizes - 600w. the 600w lamp gives an output of 155 lumens per watt (93000 lumens).
The crystal glass used offers consistant thickness which allows a more even light output. There is raised blue levels in the spectrum output. 
The design of the lamp has avoided the use of barium film which means no blackening of the glass and less gas impurities in the lamp. It also allows for a cleaner more stable light output. 
The E40 mechanical double layer base design eliminates soldering and paste and delivers a 100% inline base.

Ballasts 

Swiftair Ballast 400w

Lumii Ballast 600w

 Bulbs

400w Swiftair HPS

600w Sunblaster

Dutch Barn Reflector

LUMii 24 Hour Timer

Automate your grow room with the Axiom 24 Hour Plug In Timer

The Lumii 24 Hour Plug In Timer is ideal for setting on and off (day and night) periods with CFL, T5 and LED grow lights and timing pumps for irrigation cycles.

It is reliable and has a high quality timer unit that has been designed to take a 13 amp plug - no need to remove the plug to reset the controls.

There are 96 switching operations within a 24 hour period (every 15 minutes).

LIGHTHOUSE Tent

The LightHouse LITE 1m² Tent has extraction through the roof with a 250mm (10") sock and 2 x inline 250mm (10") socks for use with air-cooled lighting. There are also 3 x low level passive air vents with fine (anti-mite) mesh and it also includes light proof covers for when they are not in use. The LightHouse LITE 1m² Tent is ideal for use as a drying storage environment when used with the LightHouse DryNet.

The LightHouse LITE 1.2m² Tent has extraction through the roof with a 250mm (10") sock and 2 x inline 250mm (10") socks for use with air-cooled lighting. There are also 3 x low level passive air vents with fine (anti-mite) mesh and it also includes light proof covers for when they are not in use. The LightHouse LITE 1.2m² Tent fits most growing systems and is ideal for the PLANT!T aeros IV Master System.

The LightHouse LITE 2.4m Tent has extraction through the roof with a 250mm (10") sock and 2 x inline 250mm (10") socks for use with air-cooled lighting. There are also 2 x low level passive air vents with fine (anti-mite) mesh and it also includes light proof covers for when they are not in use. The LightHouse LITE 1m Tent is ideal for 2 large plants or 8 mid-size plants.

Fan Kit

FAN, ALUMINIUM DUCTING, CARBON FILTER, CLAMPS X 3

Air Flow

SMF100S - 220m3/hr High / 160 m3/h Low

2 speed switch on terminal box - Fan comes with plug

Carbon Filter Size

100mm x 250mm

To get the most out of your kit, please follow these few tips:

Remember, if you reverse-mount your PRO Filter you will lose the benefit of your pre-filter and reduce the life of the carbon.

Always mount your PRO filter as high as possible. Hot air naturally rises and so will your odours!

Try not to block too much of the filter with mounting straps or hanging devices. Use the ends of the filter to support, so not to inhibit the surface area of the filter.

Do Not mount your PRO Filter near to humidifiers. Humid air over 85% may enter the filter rendering the activated carbon ineffective and your filter may NOT neutralise odours!

Ensure you have an airtight seal around the connection of your PRO filter to ducting or extractor fan.

PLANT!T Brummie Bubbler Kit WITH 2 16.5 Litre pots!
The "Brummie Bubbler" is a hybrid growing system that effectively combines bubbling and dripping methods to produce stunning results. 
It delivers feed to a single plant via aerated nutrient solution at the root level and also via an automated drip ring - the latter of which allows you to run the system on full with the plant in place immediately after transplanting. 
For the first time ever you no longer have to initially hand water young plants growing in a bubbler related set up!
This kit contains the following:
80L Base nutrient tank (dimensions - 78L x 29H x 48Wcm)
16.5L Upper trough x 2
A precision drip watering Ring x 2
2 Large "Golf ball style" air stones
1 Nutrient Pump
1 Air pump 

all the relevant pipes and fittings.

Complete Tent Kit 0.8 x 0.8 x 1.8m

In this kit you will get the following item:

Ballast 250w ---- 250w Bulb Dual Spectrum ---- Reflector

Tent - 0.8m2

Swiftair Inline fan kit - Centrifugal fan, Carbon Filter, Alu Ducting, Clamps

Yo Yo Hanger (Pair)

Please see below for description on products:

The 250w Ballast, has been designed for improved quality and high output,

✓ Metal Case

✓ Fitted with IEC connector cord and UK mains lead

This produces the full light spectrum with added blue for the propagation and vegging stages. We recommend you replace lamps every 3-6 months to avoid diminishing harvests.

Lamp size and output

250 watt - 30,000 Lumens

Please keep the retail packaging in case you need to return it to us. Bulbs sent without the original packaging are not covered by warrant

SUPERB VALUE HYDROPONIC TENT

Quality Hydroponic Grow Room Tents

95 % reflective hammered silver lining

Heavy duty zips

Metal poles (please make sure these a pushed all the way in on the side clip provided)

5 x 150mm Air holes (2 Left, 2 Right & 1 on Top)

1 x 80mm hole

Passive ventilation windows: 2

(we found the easiest way to put up is fix bottom half first then top part and start from the back)

PowerPlant Heavy Duty Timer - Please select if needed

Normal household timers are not built to take the high inductive loads produced by HID ballasts. If used with an HID ballast - the contacts inside the timer that open and close the timed circuit will overheat and weld together - breaking the timer and leaving your grow lights permanently on.

The PowerPlant Heavy Duty Timer is different. It is designed to take high loads and has no problem dealing with the inductive loads produced by a 600w ballast.

This means no separate contactor is required and saves you money. It has a 96 switching operations within a 24 hour period (every 15 minues).

This timer is suitable for timing one 600w HID ballast. It has a robust case design with socket and timer dust/moisture covers. This unit is ideal for timing 400w and 600w ballasts. Do not use more than one 600w ballast per timer.

AutoPot 4 Pot System with 47L Tank
The 4 pot System is extremely versatile and can be used for a wide range of plant types and sizes.
Seasonal flowering plants and perennial shrubs thrive and produce an abundance of blooms and foliage because of the unique of the AQUAvalve, which is designed to only give the plant the amount of water that it requires resulting in no wasted water or over/underfeeding.
Whatever medium you choose, the 4 pot system caters for gardeners of all abilities guaranteeing great results. Once set up and the reservoir is filled with water & liquid feed, this adaptable, unfailing system will completely take care of all your plants needs with minimal monitoring.

Contents- 4x 1 pot systems supplied by a 47 litre tank

1x 47 litre tank, lid & 6mm top hat grommet
1x 6 mm golf filter
1x 6 mm cross connector
3x 6 mm T connector
4x 1pot systems consisting of:
4x Tray & lid
4x 15 litre pots
4x AQUAvalve
4x 1.5 meters of 6 mm pipe 4x Marix disc
4x Root Control Disc
Plus a full instruction leaflet.

Please choose the wattage you require above

You will receive the following

Bulb type and wattage selected x 1

E40 cord with UK plug (SW-PLUGE40) x 1

Time (please select if required) x 1

Our CFL units feature ultrahigh output compact fluorescent lamps.

E40 Screw in Fitting

Designed to help you get the best out of your plants, whilst still giving you great convenience, the CFL Lamps offer you a host of benefits:

They provide your plants with lots of usable light for best growth and yield.

They give off very little heat, meaning you can place them close to your plants for maximum output.

As the lamps are self-ballasted, you simply screw the CFL into your reflector, giving you great convenience and flexibility – as well as cost savings.

 What you will receive

1 litre - Base nutrients  Hydro,CoCo or Soil (Please select above)

250ml Katana Roots

250ml Silicon

250ml Calmag

250ml Sumo Boost or 250ml Sumo Boost Active (Please select above)

250ml PK Warrior 9/18

250ml Dragon Force

750ml Geisha Foliar

When it comes to feeding your plants and getting maximum performance and yield, we don’t like to cut any corners. 

SHOGUN Fertlisers was born out of a desire to create something special, something new for the hydroponics market. 

Not just another basic set of feeds, but something truly exceptional borne out of years of research, development and commercial application. 

We’re a UK company with a wealth of experience of what growers really want from their nutrients and additives and have created a range of products that combines exceptional performance with great value dilution rates.

Our current product range includes a series of additives as well as our newly released Hydro and Coco nutrients and we have plans to further expand this range as future products pass through our rigorous development and testing procedures.

LUMii DIGITAL Ballast
LUMii MAXii Reflector
LUMii 24 Hour plug in Timer - Please choose if needed
LUMii Sunblaster Bulb 600w
600w Digita - 250w / 400w / 600w + Boost
The LUMii® DIGITA ECO Ballast is a fully electronic ballast. This technology is micro-processor controlled and works at higher frequency (hertz) than the standard magnetic ballast meaning more light gets to your plants. It is also more efficient meaning more output per watt of energy consumed. The LUMii® DIGITA ECO Ballast is dimmable and also, has a boost setting for each lamp size meaning you can take control of the light output. 

More light output per watt of energy consumed 
With the new LUMii® DIGITA ECO Ballast less wattage is lost in the transmission of power from the wall socket to the lamp. Better power management means more light to the plant and less energy consumed. The quality of the light produced is also a lot more stable thanks to LUMii®’s power management software built into the unit that monitors for lamp degradation and power fluctuation from the grid, this produces a higher hertz rate and optimum light levels. The lamp is very quick to ignite, using less power at the ignition stage and giving your plants a full spectrum light source within 5 minutes (magnetic ballast technology takes up to 20 minutes for the lamp to come up to full brightness). 

Ultra Quiet 
The LUMii® DIGITA ECO Ballast is one of the quietest ballasts on the market with no hum or vibration (this is common with magnetic or fan cooled electronic technology). 

Ultra compact and cooler operation 
The LUMii® DIGITA ECO Ballast is one of the smallest and coolest running available, this has been achieved by creating a component set that does not generate a lot of heat. Less heat and a well-designed body shell means you can have less airspace inside the body which allows the design to be smaller. In addition, less heat means more efficient use of power and better environmental control. 

Ultra lightweight 
The LUMii® DIGITA ECO Ballast is very lightweight, the 400w & 600w is only 3kg compared with 8kg for a 600 watt magnetic ballast.

Inline fan with plug SIUK100

11L Black Trough

This 11L Black Trough is a general all round planter that can be used for DIY hydro kits and comes as part of the ‘Baby Bubbler’ kit. 

16.5L Black Trough

This 16.5L Black Trough is a general all round planter that can be used for DIY hydro kits and comes as part of the "Brummie Bubbler" kit.