Secret Jardin offers a complete range of web support to hold your plant : the WEBIT.

If your tent has a space booster – 4 horizontal bars – see section – you will be able to attach your WEBIT with the spacce booster using the CableIT provided, this will stretched them further.

Web Plant Support 60x60 cm

Web Plant Support 90x90 cm

Web Plant Support 120x120 cm

Web Plant Support 150x150 cm

Web Plant Support 120x60 cm

Web Plant Support 240x120 cm

Web Plant Support 300x150 cm

300w Swiftair Temperature Controller

The SW-TEMPSP-CON controller is equipped with an electronic temperature and speed control unit and automatically changes the speed (airflow rate) with respect to the temperature in the ventilation duct or in the premises.

The front panel of the controller has the following controls and indicators:

Speed control knob for low speed setting, Temperature control knob for temperature setting

Thermostat operating indicator (LED light)

3m long probe attached

If the air temperature increases above the thermostat set point the fan switches to the high speed (maximum airflow rate). If the temperature decreases below the thermostat set point  the fan switches to the pre-set lower speed.

The motor switches to high speed as the air temperature exceeds 2 ° C above the set thermostat set point.

Please select above which products you require 

Solutions of a known and fixed pH. These are used to calibrate pH meters. This should be done on a regular basis to ensure ongoing accuracy from the meter.

Available buffer solutions: pH 4 and pH 7

6" Clip fan or 8" Clip Fan

Quality 2 speed fan, and Off

Lower noise design,

Up/down tilt and rotate,

8" can be wall mounted if needed 

12 months Warranty,

Comes with UK Plug already wired 

CE Approved

6" 150mm doe not oscillate on its own you can turn them by hand to change the direction

PLEASE SELECT YOUR ITEM ABOVE

ROOT!T® Heat Mat - Get a jump start on plantings with the ROOT!T Heat Mat!

Adding uniform heat to your plants will speed up germination by days! ROOT!T Heat Mat offers more uniform heating than others on the market with its intricate pattern of fine wire throughout its waterproof, frayproof layers delivering the durability to withstand rugged greenhouse environments.

This mat warms the rooting area to the ideal temperature required for perfect propagation, whether seed-germination or rooting cuttings. A thermostat is also available for these heat mats offering complete temperature control.

Speeds up germination/striking of cuttings by several days
Warms root area 5.5-11˚C over ambient temperature
Fully waterproof, fray proof and durable

Sizes available:
Small - 25cm x 35cm
Medium - 40cm x 60cm
Large - 40cm x 120cm

Swiftair Digital Heat Mat Thermostat

PLEASE SELECT IF NEEDED

Electronic temperature controller is compatible with all heat mats and is an optional accessory for the Heat Mats.

The thermostat controls the temperature of heat mats evenly in colder or warmer than normal environments. It provides constant optimum temperatures for specific plants. It has an easy plug-in operation with an illuminated indicator.

Features:

Easy to use and control
Temperature control
range 20ºC to 42ºC
Controls temperature of heat mats evenly in colder/warmer than normal environments
Provides constant optimum temp for specific plants.
Easy plug-in operation
Indicator light
Simple to use
2 YEAR WARRANTY

ESSENTIALS Versions (Ess)

Digital 2 Way Thermometer/Min Max Meter (with Probe) 

Nutrient temperature measurement is via a thin waterproof probe. The Min/Max memory records the highest and lowest temperature values. Can display in °F or °C.

Digital Min-Max Thermo Hygrometer 

At the push of a button, it will display the highest and lowest values recorded since the unit was last reset. Can display in °F or °C. 

DIGITAL SERIES(LARGE SCREEN SQUARE)

Min Max Thermometer and Hygrometer 

An indoor thermometer and hygrometer which displays temperature and humidity. It can display both °C and °F and has a memory of MIN/MAX value of temperature and humidity. Other features include: - Two modes of time display: 12hr/24hr - Everyday alarm - Calendar display - Clock and date

Indoor/Outdoor Min Max Thermometer (with Probe)

This thermometer automatically changes temperature display every five seconds to show the indoor and outdoor temperatures as well as indoor humidity. It can display in both °C and °F and has a memory of MIN/MAX value of temperature and humidity. Other features include: - Two modes of time display: 12hr/24hr - Everyday alarm - Calendar display - Clock and date

Please select which Fan you require from drop down menu 

RAM 150mm Clip On Fan (6") - 15w

The RAM Clip On Fan has a quality high output with quiet motor and sturdy clips. This 150mm (6") fan has 2 speed settings and an adjustable head. It is easy to assemble with a 1.4 metre power cord and multi-region plug.

-------------------------------------------------

The RAM Oscillating Multi Fan has 2 speed settings and includes a 1.4 m power cable.

A versatile fan with multiple applications. Includes multiple clip styles meaning this fan can stand on flat surfaces, hang from a suitable wall screw (not included), clip to a horizontal object, or hang from vertical poles (16-25 mm diameter).

VitaLink ESSENTIALS

pH Down (81% Phosphoric)

pH Down Easy is a quality adjuster necessary to control the pH of nutrient solutions.  At 25% Phosphoric it is less concentrated than VitaLink ESSENTIALS Down, and allows a more gentle change in pH level. Ideal for novice growers.

pH Up (50% Potassium Hydroxide)

VitaLink ESSENTIALS pH Up Easy is a quality adjuster necessary to control the pH of nutrient solutions.  At 25% Potassium Hydroxide it is less concentrated than VitaLink pH UP, and allows a more gentle change in pH level. Ideal for novice growers.

LightHouse ECOHEAT Greenhouse Heaters

Available in 3 Sizes

45w - 305mm

80w - 603mm

135w - 915mm

Protection against sudden temperature and humidity fluctuations which can stress plants.

Helps reduce humidity and condensation when growing indoors thus protecting against fungal attack.

ideal in propagation areas where a constant ambient temperature is critical.

Cheap-to-run, the heater uses less then 50w per foot (300mm) power, similar to an ordinary light bulb and 25% less then most similar tube heaters.

More economical than a fan heater, cleaner and safer than paraffin heaters.

IP55 rated, splash and sprinkler resistant

• Memory function for 10 readings allowing for readings to be tracked easily
• Water Resistant
• Shock Resistant
• Low Battery Alert
• Simple calibration using VitaLink Essentials Calibration Fluid

• Memory Function - This allows a grower to check and log changes in the EC levels and correlate changes to potential alterations that may be taking place
• Water resistant - If the meter is accidently dropped in a solution, it will float and not break if taken out of the liquid immediately and dried quickly
• Shock resistant - Shock resistance allows for accidental dropping of the instrument without breaking
• Low Battery Alert - Gives a warning when there is 2 hours running time left, so you can change the battery in good time
• Energy saving shut-off - Turns off the meter when it is not in use
• Simple Calibration using VitaLink Essentials Calibration Fluid - Some meters can be complicated to calibrate. Simply dip the probe in the solution and press the CAL button until CAL appears onscreen.

Please select which type you require above

Precision Pruner

Surgical stainless steel holds a sharper edge longer. This ergonomic design reduces stress to the hand. The high quality spring enhances speed and performance. Double density and anti-slip handles. It is available in curved and straight blade options for superior precision.

Curved Blade Pruner

The surgical stainless steel used in this pruner holds a sharper edge longer. This ergonomic design reduces stress to the hand and the high quality spring enhances speed and performance. The Precision Curved Blade Pruner has double density and anti-slip handles and is available in curved and straight blade options for superior precision.

Bonsai Shears

For right or left handed use. These Bonsai Shears have an ultra-light simplistic design and are ideal for cutting and trimming flowers with a 60mm cutting capacity.

Mini Clippers

These convenient pocket size Mini Clippers have surgical stainless steel blades that hold a sharper edge longer. For right or left handed use.

Garden soft tie is 8 meters long. It gently secures plants with padded tie that will not cut into the stems

3.5mm x 8M 

Will Not Cut Into Stems !!

Please select which size and quantity you need above

The RAM Bug Barrier is a fine mesh screen for intake fans to prevent insects in your grow room. 

This screen comes with Velcro strips for you to attach to your intake fan to allow for easy adjustment - creating the perfect fit! 

The RAM Bug Barrier fits over your fan and the ducting can then be out over the RAM Bug Barrier.

Please note: picture shows all sizes in one picture we will only send the size and quantity order thank you

Spritz plants efficiently with this sprayer. Simply pressurise the bottle using the handy pump lid and spray! 

The handle features an on/off trigger to allow a constant stream of nutrients and water. An adjustable nozzle allows growers to choose between a fine mist or a more direct spray. 

RAM Ultrasonic Humidifier 5 Litre

The RAM Ultrasonic Humidifier allows the grower to increase the humidity of the growing environment up to 400ml / hour. 

Complete with a 5L tank, this humidifier is fully adjustable and easy to use. Power - 30w Voltage - 220-240v

RAM Ultrasonic Humidifier 13L

The RAM Ultrasonic Humidifier 13L Tank offers the biggest tank capacity of any humidifier on the hobby market. 

It has a humidification rate of 1100ml per hour and offers an analogue control allowing you to set the unit to produce the amount of humidity that you need. Four nozzles and an extra hole allow you to get an even distribution of mist in your growing environment.

The unit also offers auto cut-off which protects the humidifier in cases where your water reservoir becomes empty.

Use VitaLink ESSENTIALS Buffer solution to calibrate pH meters. 

This pH 4 Buffer solution gives an accurate representation of the pH scale at pH4 to measure against.

Use VitaLink ESSENTIALS Buffer 7 for a 2 point calibration scale. 

This will give an accurate range of measurement that hydroponic nutrients work within.

Perfect for use with the ESSENTIALS pH meter

Use ESSENTIALS calibration solution to calibrate EC/CF meters. Set to read CF28 at room temperature.

 NOTE: All calibration solutions should be at room temperature (20°C) for successful and accurate calibration. Use with ESSENTIALS EC Meters.

The grow gadgets laser thermometer is a compact, lightweight and low cost infrared thermomenter, ideal for use around your grow space.

To use simply aim at your desired location and pull the trigger to display the temperature of the item being measured.

ONA - Odour Neutralising Agent 
Hydroponics Air Freshener

Ona are one of the most well known brands in the Hydroponic world. Offering exceptional odour neutralising and air freshening capability, these Blocks and Gels are truly remarkable. Customers return again and again for this long lasting odour control.

Available in a solid 250ml block, 1 or 3 litre Gel.

Gel - ideal for longer term deodorising of closed spaces. Can be used with a fan for greater effect.

Block - ideal for ventilation systems and small closed environments such as closets

Each contains a carefully blended combination of scent and absorbent material to keep odours under control.

The Gel is comprised of a liquid and a gel to ensure a controlled release and excellent dispersion.

Periodic replacement is required.

The PLANT!T YoYo tightens as your plant grows, eliminating the need to re-hang everyday.

It comes with a 1.4m fully retractable line and is ideal for fruiting crops e.g. tomatoes or other vine crops.

Designed to secure and support as well as train a variety of unruly or heavy cropping plants in their desired position.

Can also be used to support heavy cropping trusses.

Simply wrap around your plant and secure around the stem with the hook and watch your plants grow straight and true.

"YoYo's are a very useful device for the tomato grower and I shall be using them every season from now on!" - Nick Chenhall - Tomato Growing

X-Stream Aeroponic Propagation

Want to root cuttings faster, with a near 100% success rate and no root rot or drying out?

Then choose the X-Stream aeroponic propagator. The Xstream mists cuttings to maintain ideal moisture and oxygen levels.

Cuttings are suspended in mesh pots in the propagator’s misting chamber and are constantly misted.

DESCRIPTION

The X-Stream Aeroponic propagator creates perfect conditions for cultivating cuttings reliably and quickly.

The mist prevents root rot and drying out and provides unrestricted access to oxygen, the large vents in the lid provide humidity control, and the heated version enables you to raise cuttings in an unheated area all year.

Because the mist is constant, there’s no need to monitor water levels every day.

A higher % of your cuttings will root (many growers report 100% success rates) and the plants will be faster growing and more resistant to stress and disease throughout their life thanks to their incredibly healthy start.

X-Stream Aeroponic propagators have grooves in the lid to fit the Sunblaster T5 propagation lights. These nanotech enhanced lights run cool enough to be placed onto the propagator lids with zero risk of damage.

WHY THEY ARE GREAT

The X-Stream creates the perfect environment for root development which dramatically improves the success rate of cuttings and speeds up their root development. The condition of the cuttings can be checked quickly with minimal impact on the cutting ensuring that the cuttings are as healthy as possible when they are potted on.

X-Stream propagators have specially designed lids to fit Sunblaster T5 lights. Simply place the light onto the lid and your ready to grow. – SEE EBAY ITEM NUMBER – 262916423681

System Size L x W x H cm   -    Tank Volume    -    No. of plants

12 Site Propagator   -   59 x 46.5 x 44   -   8 Litres   -   12

20 Site Propagator   -   59 x 46.5 x 44   -   8 Litres   -   20

40 Site Propagator   -   77 x 40.5 x 45   -   14 Litres   -   40

120 Site Propagator   -   115 x 64.5 x 46    -   40 Litres   -   120

HINTS AND TIPS

Pump - leave the pump on 24/7~

Feeding - when roots begin to show add nutrients at a quarter of the manufacturers recommended dosage.

Ventilations - once roots are showing, open the vents slightly. Gradually increase the opening every day and remove the lid completely to harden off for a couple of days before transplanting on.

Rooting gels and powder can still be used. When the cutting is dipped, all active ingredients are absorbed immediately and will not be ‘washed off’ by the misting.

Transplanting into soil or coco

Remove from the X-Stream when roots begin to poke through the mesh pot. Pot on into 3” or 4” pots and grow on for a few days before transplanting on.

Transplanting into hydro

Remove from the X-Stream when roots have grown 3” to 4” from the bottom of the mesh pot. Transplant directly into the hydro system.

Transplanting into rockwool

Remove from the X-Stream when roots have grown 3” to 4” from the bottom of the mesh pot. Punch a hole in the bottom of a 3” or 4“ cube, sandwich the cutting between two halves of an Grodan SBS cube allowing the roots to trail through the punched hole. Transplant immediately.

Identify insects and diseases

All active eye products have a pest identifier included.

Active Eye Microscope (60x - 100x)

The compact design provides 60x to 100x magnification and houses a built in light and a zoom lens.

Simply place the base of the microscope on to the specimen and adjust the focus by gently turning the focusing dial until your item comes into perfect view.

comes with protective pouch and instructions

batteries included

Active Eye Microscope (100x)

The compact design provides 100x magnification and houses a built in light.

simply place the base of the microscope on to the end of the specimen.

comes with protective pouch and instructions

batteries included

Magnifier Loupe (30x)

A great little magnifier that gives you 30x magnification

Provides a sharp, clear, enlarged image without distortion and features a swing away protective lens cover that also serves as a handle.

Comes with protective case and instructions.

A humidifier is a key component to making your grow room the best environment possible. Using a humidifier, you are able to control the humidity in your grow room environment. Allowing you to reach the optimum level of humidity for your plants. The RAM Wall Humidifier is a wall mounted unit allowing for extra floor space without sacrificing your grow room environment. The easy-to-use humid-stat control dial allows for a simple control system from 20% to 100% humidity. The RAM Wall Humidifier as a stand-alone product or can be used alongside a Water Filter Kit.  Users in hard water areas are particularly recommended to use a water filter with the humidifier, to protect its longevity.

Key USPs:

Prevent dryness in your growing environment

Easy-to-use dial humidistat control

Up to 1600 ml/hr output

No refills required – mains water connection (all fittings included)

Features and Benefits

Mains water connected – means a continual supply of water. As a result, there is no need to keep topping up the humidifier, leaving your machine always ready for use.

Easy to use dial humid-stat control – simple control. Allowing controlling your humidity to become a straightforward task.

Wall mounted fitting – growers can enjoy outstanding RAM quality along with efficient usage of their grow room space.

Technical Specifications

Input     220-240 V AC | 50 Hz

Power   120 W

MAX. Output     1600 ml/hr

Science behind the product

An ultrasonic humidifier uses a ceramic diaphragm vibrating at an ultrasonic frequency to create water droplets that quietly exit the humidifier in the form of cool fog/mist.

Available in 5cm or 10cm depth

An innovative solution for grow rooms with restricted access points, these flexible trays fit where other trays can’t go. Can be used as a catchment tray or to keep work spaces clean, these durable trays are manufactured in-house, ensuring high quality.

Time Display

Indoor Temperature Range: -10 to 50 Degree C

Humidity Range: 20% to 95%

Shows: Min / Max

Shows: Too Dry - Comfort Zone - Too Wet

Why use the Smart CO2 Bag?

The Smart CO2 Bag is very small and easily affordable bag producing carbon dioxide for your plants. It can multiply the growing speed of your plants and make fruits ripen faster improving taste, color and crops.

The Smart CO2 Bag is safe to use, easy to setup without any maintenance required. It is the smallest and by far the most effective solution available on the market.

What is carbon dioxide?

Being like the oxygen to us humans, carbon dioxide is one of the most important components of growing up plants. All plants need carbon dioxide to grow. If a plant cannot get enough carbon dioxide from the air, it will grow slower. The Smart CO2 Bag is a powerful and easy way to add more carbon dioxide to your green room without overspending.

How To Use the Smart CO2 Bag

When and where to use it?

Get a Smart CO2 Bag 2-3 weeks after planting your seeds. Make 6 holes in top of the bag and hang it above your plants. In large green rooms, hang the bag over the aisles. TheSmart CO2 Bag only produces carbon dioxide in temperatures above 18 ºC (64 ºF). Store the closed bag in a dry and cool place under 18 ºC (64 ºF).

How long does it last?

When the Smart CO2 Bag comes into contact with oxygen, it will start producing carbon dioxide. However it can take a few days before production starts. Depending on the air circulation in the green room, one Smart CO2 Bag will produce enough carbon dioxide for an area of 10 m2 (170 ft2) for up to 3 months

How to maximize the benefits?

With the extra carbon dioxide, your plants can withstand temperatures that are 3-5 ºC (5-9 ºF) higher than usual.

COMPACT SIZE, MAXIMUM OUTPUT!

1350 - 1500 PPM!!!

(IN 10M X 10M AREA)

Keep out of reach of children

We cannot stress enough the importance of maintenance and storage solutions. Expensive equipment is often utilised well below its full capabilities due to lack of proper maintenance of sensors.

pH probes should always remain in Meter Store when not in use to prevent the probe from drying out. With VitaLink ESSENTIALS Meter Store, keeping pH probes in tip top condition is no longer a problem.

Includes probe foam to cut to the size of your meter cap to assist in keeping the probe wet.

Also available Essential pH Meter and PLANT!T pH meter

Remove foul odours naturally 

They don’t just mask odours - they neutralise odours using an essential oils based formula that seeks and destroys organic and non-organic odours, replacing it with your choice of scent.  

Simply remove the lid or spray and let the active ONA ingredients evaporate and neutralise any odours they come into contact with, permanently and efficiently. It’s as easy as that.

• Choice of many Scents
• Strong essential oils based formula
• Doesn’t just mask foul odours – it eliminates them
• Reliable and long-lasting odour control
• Permanently removes even the most stubborn of smells
• Completely organic

The PLANT!T pH meter is reliable and easy to use. Small and lightweight, it is ideal for any growroom.

The PLANT!T pH meter features:

The LCD dual display shows pH and tempeature readings

Calibration is easy with a one touch autocalibration and can give upto a 3 point calibration

The meter is IP65 waterproof rated

The reach through mesh allows the trellis netting to handle more weight and remain taught and therefore provide stronger support.

This product is non tangle which can be a common problem with netting.

Why use the Smart CO2 Bag?

The Smart CO2 Bag is very small and easily affordable bag producing carbon dioxide for your plants. It can multiply the growing speed of your plants and make fruits ripen faster improving taste, color and crops.

The Smart CO2 Bag is safe to use, easy to setup without any maintenance required. It is the smallest and by far the most effective solution available on the market.

What is carbon dioxide?

Being like the oxygen to us humans, carbon dioxide is one of the most important components of growing up plants. All plants need carbon dioxide to grow. If a plant cannot get enough carbon dioxide from the air, it will grow slower. The Smart CO2 Bag is a powerful and easy way to add more carbon dioxide to your green room without overspending.

How To Use the Smart CO2 Bag

When and where to use it?

Get a Smart CO2 Bag 2-3 weeks after planting your seeds. Make 6 holes in top of the bag and hang it above your plants. In large green rooms, hang the bag over the aisles. TheSmart CO2 Bag only produces carbon dioxide in temperatures above 18 ºC (64 ºF). Store the closed bag in a dry and cool place under 18 ºC (64 ºF).

How long does it last?

When the Smart CO2 Bag comes into contact with oxygen, it will start producing carbon dioxide. However it can take a few days before production starts. Depending on the air circulation in the green room, one Smart CO2 Bag will produce enough carbon dioxide for an area of 10 m2 (170 ft2) for up to 3 months

How to maximize the benefits?

With the extra carbon dioxide, your plants can withstand temperatures that are 3-5 ºC (5-9 ºF) higher than usual.

COMPACT SIZE, MAXIMUM OUTPUT!

1350 - 1500 PPM!!!

(IN 10M X 10M AREA)

Keep out of reach of children

Single Socket Controller

The SMSCOM MK2 Smart Fan Speed Controller really is a smart piece of kit for automatically controlling the running speed of just one fan or with an extension lead multiple fans, to maintain your grow room at the temperature you require.

If using Multiple Fans please do not Exceed 6.5A

The SMS Smart Fan Speed Controller has built in software that constantly reads the temperature from the probe and then adjusts the running speed of the fan to suit, either faster to cool the room down or slower to heat it up.

The SMS Smart Controller is a plug and play unit that involves no wiring, simply plug in your fan and set your desired temperature and then let this smart controller do the rest.

If you use a grow tent with just one fan for extraction and fresh air passively pulled in, the SMS Smart Fan Speed Controller is the ideal partner to automatically maintain the ideal running speed for your extraction fan.

5 year Warranty - Software controlled - Smooth fan speed adjustment - Optimise grow room temperature - Constant air flow - Plug and play – no wiring necessary - 2m Temperature Sensor (Optional) - Minimum fan speed can be adjusted

Accurate to +/- 1 degree - MAX Load 6.5A

Twin Controller - 4.5 or 7amps

Control your temperature with the speed of your fans – all you need is an SMSCom controller.

Your intake and extractor fans will speed up if your room needs cooling, or slow down if it needs heating (temperature sensor included).

Don’t worry about air exchange – you can set minimum and maximum fan speeds.

It’s easy to set up! No hard wiring’s needed. Just plug your fans in, then set your target temperature, min speed & max speed using the 3 dials.

If you need a longer power cable, you can quickly plug it into your controller's IEC socket (like what lots of kettles have!). 

For safety, each controller has a replaceable fuse. 

Overall, your controller can handle a total 4.5 Amps to 7 amps depending on the controller selected. 

• Tidy, small & easy to use

• No hard wiring needed

• Save energy – fan speed slows when you need it to

• Easy to connect - plug and play!

• Simple to program (via 3 dials)

• Power cable included (90cm)

• Temperature sensor included

• Min speed: ensure there’s adequate air exchange

• Max speed: ideal for oversized fans

• Handles 4.5 Amps in total

• Protective, replaceable 4.5 Amp fuse

• IEC power cable connection

• Features 2 x 3 pin UK plug sockets

ENDOSAN HYDRO TEST STRIPS - LOW RANGE (1-100PPM)

EndoSan Hydrogen Peroxide test strips are simple and quick to use. They quickly measure peroxide levels in water and provide a visual aid to ensure enough EndoSan is in use.

The low range test strips measure peroxide levels up to 100ppm.

How to use:

1. Dip for 2 seconds

2. Shake

3. Wait 30 seconds

4. Compare to testing chart

Each vial contains 100 test strips.

ENDOSAN HYDRO 8 WATER DISINFECTION 1L

EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.

EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.

When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.

Key Benefits

Highly effective biofilm remover

Unrivalled stability

Forms no harmful by-products

Non-toxic & pH neutral when dosed

Proven efficacy & globally approved

Effective between 0°C and 95°C

Odour, colour and taste free

Three year shelf-life

DEFRA Approved Disinfectant

How Does it Work?

A typical bacterium naturally emits a negative charge. EndoSan is attracted by this charge to the site.

In catalase producing bacterium the presence of EndoSan inhibits the defence mechanism, allowing the powerful free hydroxyl radicals to attack the cell membrane.

These free hydroxyl radicals penetrate the membrane and destroy the bacterium. Once killed the bacterium no longer emits a negative charge.

EndoSan is now attracted to the next bacteria site emitting a negative charge. Silver ions re-stabilise with excess hydrogen peroxide molecules to repeat the process.

ENDOSAN HYDRO 3 SURFACE DISINFECTION 500ML

EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.

EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.

When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.

Key Benefits 

Highly effective biofilm remover 

Unrivalled stability 

Forms no harmful by-products 

Non-toxic & pH neutral when dosed 

Proven efficacy & globally approved 

Effective between 0°C and 95°C 

Odour, colour and taste free 

Three year shelf-life 

DEFRA Approved Disinfectant

How Does it Work? 

A typical bacterium naturally emits a negative charge. EndoSan is attracted by this charge to the site.

In catalase producing bacterium the presence of EndoSan inhibits the defence mechanism, allowing the powerful free hydroxyl radicals to attack the cell membrane. 

These free hydroxyl radicals penetrate the membrane and destroy the bacterium. Once killed the bacterium no longer emits a negative charge.

EndoSan is now attracted to the next bacteria site emitting a negative charge. Silver ions re-stabilise with excess hydrogen peroxide molecules to repeat the process.

ENDOSAN HYDRO 3 SURFACE DISINFECTION 5L

EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry. 

EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe. 

When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.

Key Benefits 

Highly effective biofilm remover

Unrivalled stability

Forms no harmful by-products

Non-toxic & pH neutral when dosed

Proven efficacy & globally approved

Effective between 0°C and 95°C

Odour, colour and taste free

Three year shelf-life

DEFRA Approved Disinfectant

How Does it Work? 

A typical bacterium naturally emits a negative charge. EndoSan is attracted by this charge to the site.

In catalase producing bacterium the presence of EndoSan inhibits the defence mechanism, allowing the powerful free hydroxyl radicals to attack the cell membrane. 

These free hydroxyl radicals penetrate the membrane and destroy the bacterium. Once killed the bacterium no longer emits a negative charge. 

EndoSan is now attracted to the next bacteria site emitting a negative charge. Silver ions re-stabilise with excess hydrogen peroxide molecules to repeat the process.

ENDOSAN HYDRO 8 WATER DISINFECTION 5L

EndoSan is a solution of Hydrogen Peroxide (H₂O₂) which is stabilised using a proprietary ionic silver based chemistry.

EndoSan is a powerful, highly effective, broad spectrum disinfectant that is both stable and safe.

When correctly applied to water, air or any surface EndoSan will disinfect through an oxidisation process and continue to safely provide unrivaled residual performance.

Key Benefits 

Highly effective biofilm remover

Unrivalled stability

Forms no harmful by-products

Non-toxic & pH neutral when dosed

Proven efficacy & globally approved

Effective between 0°C and 95°C

Odour, colour and taste free

Three year shelf-life

DEFRA Approved Disinfectant

How Does it Work 

A typical bacterium naturally emits a negative charge. EndoSan is attracted by this charge to the site.

In catalase producing bacterium the presence of EndoSan inhibits the defence mechanism, allowing the powerful free hydroxyl radicals to attack the cell membrane.

These free hydroxyl radicals penetrate the membrane and destroy the bacterium. Once killed the bacterium no longer emits a negative charge.

EndoSan is now attracted to the next bacteria site emitting a negative charge. Silver ions re-stabilise with excess hydrogen peroxide molecules to repeat the process.

The PLANT!T® Circular Water Timer can be used with mains water from a tap outlet or with a gravity feed system from a tank, water butt or reservoir. Simply select the time you want the water supply to be turned on and off, link up to your irrigation dripper line and the timer will do the rest.

No plumbing needed- easy to install and simple to use. The water timer is also weather resistant and has an auto safety valve shut off for when the battery is low.

Guard 'n' Aid for SpiderMite

Guard 'n' Aid for SpiderMite is a Pyrethrum based target contact insecticide to be used against SpiderMite and their eggs.

Supplied in a 250ml concentrate to make 15 x 750ml sprays (Spray Pistol will need to be purchased Separately)

Guard 'n' Aid for Thrip

Guard 'n' Aid for Thrip is an insecticide specially developed for use against Thrips at larval, adult and egg stages.

Suitable for outdoor and protected growing on both edible and non-edible crops.

Supplied in a 250ml concentrate to make 22 x 750ml sprays (Spray Pistol will need to be purchased Separately)

Guard'n'Aid Insect Catcher

Catch and identify your pests with this pack of five double sided glue sheets used to monitor the presence of all flying insects. Use sticky fly traps as part of your routine integrated pest management (IPM) procedure to alert you to a problem before it becomes an infestation.

Guard'n'Aid DiatoMITE

DiatoMITE from Guard'n'Aid is a diatomaceous earth dusting powder which can be applied to plant leaves and surrounding soil to create an inhospitable environment for insects.

Diatomaceous earth is a natural powder made up of fossilised silica diatoms which has many qualities and uses:

Guard'n'Aid DiatoMITE naturally draws away all the essential moisture that insects require to grow, making plants and leaves uninhabitable environments.

It can be liberally applied in and around the home including the garden when the weather is dry.

Guard'n'Aid DiatoSHIELD

Guard'n'Aid DiatoSHIELD is granulated, calcined diatomaceous earth (1-3mm) and is suitable for a wide range of gardening and horticultural applications. It can be used on lawns and beds as a soil improver to prevent compaction, improve aeration, structure and drainage. It could also be used in pots and containers for the same reason as well as a drainage layer to prevent water logging or a top dressing to reduce water loss and discourage pests such as Fungus Gnats and other Sciarid Flies by preventing them laying eggs in the growing media.

Guard'n'Aid CleanRoom 1L

Used for sterilising your greenhouse, growroom, trays & pots, propagation, equipment and tools.

Kills 99.999% of Bacteria

Kills 99.9% of Botrylis and Fusarium

Effective against Pythium

Naturally derived Biocide

Guard'n'Aid CleanRoom is a powerful, naturally derived cleaner and disinfectant based on fermentaton extracts and plant -derived surfactants. Can be used on all hard surfaces such as metal, glass, plastic, wood, vinyl and painted surfaces.

Guard'n'Aid Healthy Root

A concentrated preparation of naturally-occurring bacteria to promote plant and root health in hydroponics and soil-based systems. it restores the microbial balance by adding beneficial bacteria, improves nutrient availability and uptake and will ensure that your roots grow strong and healthy even in the harshest of conditions. Use alongside your standard nutrient program or as a boost when you see stress or browning of roots. In no time at all healthy white roots will grow back and your harvest will be assured.

Guard 'n' Aid PestOFF Plus Concentrate 250ml

Guard 'n' Aid PestOFF PLUS contains the active ingredients of natural Pyrethrum and Rapeseed oil.

A broad spectrum Pyrethrum-based contact insecticide for the control of many sucking and biting insects including White Fly, Aphids, Thrips, Mites, Scale Bugs, Caterpillars, Wool Bug, Mealy Bug, Beetles and some Wasp larve. Effective against adult insects, larvae stages and eggs.

Supplied in a 250ml concentrate to make 22 x 750ml sprays (Spray Pistol will need to be purchased Separately)

Guard'n'Aid PestOFF Plus Fumer

New & improved Guard'n'Aid PestOFF Maxi Fumer - Permethrin based smoke generators for use in controlling crawling and flying insects in difficult to reach places, grow rooms, empty glasshouses.

Mini (Pack of 2) - 2 x 3.5g Smoke Generators

Midi - 1 x 15g Smoke Generators

Maxi - 1 x 31g Smoke Generators

Biobizz Leaf-Coat 500ml (inc Spray Nozzle)

What is Leaf·Coat™?

Leaf·Coat™ is a ready-to-use product that strengthens the plant en protects the plant against unwanted insects and molds. Leaf·Coat™ is a product made from natural latex that was developed to restrain evaporation.

Within a few hours after application, a very thin elastic layer forms around the leaves. This natural latex creates a protective, permeable, self-degradable layer on the leaf, while at the same time it allows the passage of air and light. This thin layer is however effective enough to protect the plant against pests and diseases.

How to use Leaf·Coat™

Leaf·Coat™ does not have to be mixed with water, but is ready for use. For the best results we advise to apply Leaf·Coat™ by using an atomizer. Spray the leaves and flowers of the plant completely, repeat this about two times a week. Leaf·Coat™ can be used till two weeks before the end of the flowering period.

Note: Leaf·Coat™ will not be absorbed by the leaves; therefore it will not affect the taste of the fruit.

Protection layer that is formed by Leaf·Coat™

When the plants are in an atmosphere that is too hot and humid (over 28 degrees Celsius), the plants can lose a great quantity of water by evaporation through the leaves.. By using Leaf·Coat™, a layer of natural latex is formed around the leaf, which avoids the plant from "sweating".

On the other hand, using Leaf·Coat™ at lower temperatures (especially in winter), protects the leaves against cold. The natural latex formed by Leaf·Coat™ helps to maintain the temperature.

Floor Film

 Floor Film has been specifically designed for use on the floor of a grow room

This handy little leaf trimmer goes together easily. Simply insert the legs into the holes provided and attach the mesh catch bag, plug in, and it is ready to use.

Please make sure you wear safety eye wear and tight gloves when operating.

This trimmer has sharp rotating blades that may, through carelessness cause injury to fingers.

Easy to put together & even simpler to use

A quick & effortless way to trim

Compact design only requires 4ft of space

Easily accessed for maintenance

Equipped with a Powerful, efficient and quiet motor

220-240v 50Hz

Designed with auto-shut off when cutting box is opened

1 YEAR WARRANTY

Use your mobile to take amazing magnified photos and videos.

 Attach this phone scope directly to your mobile or tablet, aligning the microscope lens with your device's camera lens.

 This device allows you to zoom up to 30x magnification using your device's digital zoom!

The LightHouse Wireless Thermostat is easy to use and set-up. 

The plug and play unit can control heating or cooling equipment by altering the setting.

The AirComfort is a temperature and humidity sensor that will help growers manage their grow space conditions with ease.

The device wirelessly connects to any smart phone and growers can use the Air Comfort app to recieve, record and store temperature and humidity data.

It can also take recordings from every 5 minutes up to every 40 minutes and store up to 100 days worth of data depending on recording setting.

You can also set alerts for when the temperature or humidity changes so you are always in the know.

Target nutrient temperature: 18oC - 21oC Keep your nutrient solution cool to speed up nutrient uptake and fight root problems 

use Iceline Pipe. To keep heat out, Iceline Pipe has two layers - a black layer to block UV rays – a white layer to reflect heat. You can expect a temperature drop of at least 3oC – 8oC when you switch to Iceline Piping. 

As result, your oxygen level will increase, which will improve nutrient uptake and lower the risk of root problems. 

It’s simple, but it works. During summer, Iceline is the only pipe to use. 

• Keeps your nutrient cool

• Temperature drops by 3oC – 8oC

• Double wall to keep heat out

• White outer layer to reflect heat

• Black inner layer to block UV rays

• Prevents root problems (like Pythium)

• Helps improve nutrient uptake

• Maximises oxygen level

Overview

Eliminate hot spots and high humidity zones with the ultimate air diffuser

Air circulation is a vital factor in achieving optimum environment and therefore greater results. 

Can be mounted directly to any Centrifugal (STUBE) or Mixed flow fan (XFLO range). 

The aerodynamic design ensures airflow is evenly distributed throughout the grow environment to eliminate hot spots and high humidity zones, creating an ideal atmosphere for plants.

Features

Metal aerodynamic diffuser designed to ensure an even supply of air around the grow room.

Mounts directly to the fan for optimum air diffusion. (please note some adjustment might be needed - Screws not provided)

Eliminates hot spots and high humidity zones.

The ultimate destratification accessory for grow rooms.